For your situation, I would suggest being pretty cautious with those generic listings you see on Amazon because the Moto G Stylus (2025) silo is actually kinda specific. In my experience, even if a third-party stylus says it fits, the dimensions are sometimes off by like a fraction of a millimeter, and that's enough to make it get stuck or rattle around... basically a nightmare lol.

Here is what I recommend looking into:

1. Stick with the Motorola+Official+Replacement+Stylus+for+Moto+G+Stylus+2025&linkCode=osi&------123456890?5422-20" target="_blank" rel="nofollow sponsored">Motorola Official Replacement Stylus for Moto G Stylus 2025 if you can find it in stock. It's usually around $15-$20 and you wont have to worry about the palm rejection acting up.
2. If you do go third-party, make sure it mentions "passive capacitive" tech specifically for the 2025 model. Brands like iSpro Replacement Stylus Pen for Moto G Stylus are usually okay, but the tip durability is hit or miss compared to the OEM one.

Basically, the 2025 model uses a basic capacitive tip, so it doesn't have the same crazy active pressure sensitivity as a Galaxy S-Pen, but the "palm rejection" is actually handled by the phone's software detecting the stylus proximity. If the tip material is too hard or too soft, the screen might not register it right and youll get skipped lines while writing. Honestly, I'd say just pay the extra $5 for the official one from the Moto site or a reputable seller. It'll save you the headache of it potentially getting stuck in the silo! gl!

Check out iFixit or eBay if youre looking to save a few bucks. Honestly, I tried a cheap Generic Replacement Stylus for Moto G from Amazon and it was a total disaster—it literally got stuck in the silo and I had to use tweezers to get it out. Such a bummer... if u want to stay under $25, iirc you can sometimes find an open-box Motorola+Moto+G+Stylus+2025+Replacement+Pen&linkCode=osi&------123456890?5422-20" target="_blank" rel="nofollow sponsored">Official Motorola Moto G Stylus 2025 Replacement Pen on eBay for like $15. Better than risking ur phone with a knockoff imo!

Similar situation here - I actually went through this last year with my previous Moto and it was such a headache. Basically, I tried to save a few bucks and bought a cheap pack from a random seller because I thought they were all the same. Big mistake!

1. The first one I tried felt super scratchy on the glass, almost like it was gonna leave permanent marks.
2. Even worse, the fit was so tight that I honestly thought I'd have to take the phone apart just to get it out of the silo.
3. I eventually just gave up on the knockoffs because the safety of my phone wasn't worth saving $10.

So yeah, my current setup is just the one I got directly from the manufacturer's site. It cost a bit more, but the peace of mind knowing it won't ruin the internal spring mechanism or scratch the screen is worth it tbh. I'm much happier now that I don't have to worry about it getting stuck again lol.

Ok so I actually lost mine last month too lol. Tbh just stick with the official Motorola replacement! It fits the silo perfectly and still feels sooo smooth, unlike those cheap ones... plus its usually under $20.

Ok so, if ur like me and prefer the DIY/repair enthusiast route, I usually skip the big retail sites and look at what the pros use. Basically, if you want the exact fit without the markup for the 2025 model, here's my advice: - Check wholesale suppliers like Injured Gadgets or MobileSentrix. They sell "OEM Grade" components to repair shops. Since their business relies on professional techs, the parts usually have much tighter tolerances than random third-party listings, so it won't get stuck in the silo.
- Look specifically for "OEM Pulled" parts on specialist sites or reputable electronics recyclers. These are genuine parts taken from units with broken screens or motherboards. It’s the best way to keep that original pressure sensitivity for under $15.
- Also, consider picking up some BW-100 Electronic Contact Cleaner. If the silo feels tight, it’s often just pocket lint or grime. A tiny spray inside can make any replacement slide in way smoother. Tbh, finding a "pulled" original is the only way I’ve found to guarantee that 1:1 performance without paying the full retail premium.

Seconded!